HomeWho we serveTradesConcrete

Trade · Concrete · CSI Division 03

Cubic yards that match the pour ticket, not the take-off guess.

Concrete takeoff mixes volumes, areas and lengths on the same sheet — footings and slabs in cubic yards, formwork in square feet, edge form and control joints in linear feet. PiloBuild keeps each quantity in its own class instead of folding everything into one number that nobody can audit back to a pour.

Concrete finishers leveling a commercial slab with a straight screedT-01 · Concrete
Drawing reading

The drawing-reading problem: one polyline, three quantities

A slab boundary on a foundation plan is a single closed polyline. From that one polyline a concrete estimator needs three different numbers: the slab area in square feet for the flatwork, the perimeter in linear feet for edge form, and — once thickness is applied from the detail callout — a volume in cubic yards for the pour. Miss the thickness callout on a thickened-edge slab and the CY number is wrong even though the polyline was traced correctly.

Footing schedules compound the problem: a continuous footing is a linear run measured in LF, but it is priced and ordered in CY once width and depth from the footing schedule are applied, and the schedule lives in a table on a different sheet than the plan view.

Objects + units

What gets measured, and in what unit

Six object classes cover a typical concrete package. Each keeps its own unit instead of being folded into a single blended quantity.

Takeoff objectUnitHow PiloBuild resolves it
Footings & foundation wallsCY (volume), LF (wall/footing run)Width and depth from the footing/wall schedule, applied to the plan polyline.
Slabs on grade & elevated slabsCY (volume), SF (area)Thickness from the slab detail or section callout; area from the closed boundary.
FormworkSF (contact area)Vertical face area on walls, footings and slab edges — not the same number as slab SF.
Edge form & control jointsLFPerimeter and interior joint layout read from the plan, not estimated as a percentage of area.
Reinforcing & embedsLB or EA, by size and spacingRebar schedule quantities and embedded-item counts cross-referenced to the pour they belong to.
FinishesSF, by finish classBroom, trowel, or sealed finish called out per area, since labor rates differ by class.
Resolution

Classification, resolved before the quantity is produced

Vector-first ingestion keeps the slab, footing and wall polylines as coordinate geometry, so area and perimeter come from arithmetic on the actual boundary rather than a traced approximation. Classification resolves each element to its detail callout and section cut, so a thickened-edge slab or a stepped footing picks up the correct thickness or depth before volume is computed, and the result is grouped by pour: footings, slabs on grade, elevated slabs, and walls, each with its own CY and formwork SF.

A schedule value change (a footing depth revised from 24″ to 30″) is one of the discrepancies the BOM cross-check is built to catch between the design-intent structural sheet and a subcontractor’s shop-drawing takeoff, before it becomes a change order at the footing inspection.

Output

What you get back on a concrete package

Quantities by class

Every concrete object above, grouped the way your estimating desk already groups it, with the unit that matches how it is bought.

A geometry audit trail

Each quantity links back to the sheet, the resolved callout or schedule row, and the scale a person confirmed.

A BOM cross-check

Design-intent drawings compared against a subcontractor shop-drawing takeoff on the same scope, with discrepancies listed before they reach the field.

Review

3 questions, specific to concrete

What CSI division does Concrete takeoff fall under?

Primarily CSI Division 03 (Concrete). Related sections we classify against on a typical concrete package include: 03 30 00 Cast-in-Place Concrete, 03 20 00 Concrete Reinforcing, 03 10 00 Concrete Forming and Accessories.

Does PiloBuild replace our estimator on this trade?

No. PiloBuild produces the measured quantities, grouped and classified the way this page describes, and a bid summary showing the arithmetic behind the cost build-up. Your estimator applies judgment, reviews the classification, and owns the number that goes on the bid. The scale confirmation and the review-and-approve gate exist specifically so a person checks the machine, not the other way around.

What happens when the drawing set is incomplete or the schedule is missing?

Where a callout cannot be resolved — a wall-type tag that does not match any schedule row, a size annotation with no nearby segment to attach to — the item is flagged rather than guessed. An unresolved item is reported to your team for a manual read, not silently dropped or estimated with a default.

Next step

Run a pilot on a concrete set.

Bring one drawing set and the estimate you already have. We measure it, you compare it line by line.

Call PiloBuild+1 (872) 804-7023